:: Precision Fences
    Router Table Fences
    Table Saw Fences
    INCRA I-BOX new
    Router System Accessories
    Router Tables & Stands

 :: Miter Gauges
    Miter Express
    Miter V27
    Miter V120
    Miter V120 Shopsmith
    Miter 1000
    Miter 1000HD
    Miter 1000SE Telescoping Fence
    Miter 3000
    Miter 3000SE Telescoping Fence
    Miter 5000 Miter Sled
    Miter Gauge Combo Pack
    Miter Accessories
    Comparison Chart

 :: Measuring, Marking & Layout
    Squares & Angles
    Marking Rules
    Bend Rules
    T-Rules
    Specialty Rules
    Custom Rules
    Rule Sets
    INCRA Gauge

 :: Jig & Fixture Components
    Build-It System
    Tracks
    T-Tracks
    Miter Sliders
    Miter Channels
    Right Angle Fixture

 :: Books, Plans, Videos &
    Accessories

    Free Plans
    Instructional Videos
    Books & Plans
    Stops
    HingeCrafter

 :: Become an INCRA Insider
 :: Photo Gallery
 :: Perry’s Tool Zone
 :: Parts & Components
 ::
INCRA Awards


 >> IncrementalTools.com
 
 
See what's the latest woordworking tools from INCRA. You can also receive our new product announcements, special offers and information about our products by becoming INCRA Insider.


New and improved! Allows precise height adjustments and change router bits above the table. Direct-drive, super low friction, and it’s compatible with wide variety of fixed base routers without the need for adapters.

Fits every INCRA router table!

As with our custom INCRA Mast-R-Lift-II, the PRL-V2’s top plate is a super flat Blanchard-ground casting that’s machined to accept INCRA’S unique MagnaLOCK reducing ring system.


If you’ve been putting off the purchase of one of woodworking’s most exciting tools because it was not available in a Metric model, your wait is over. INCRA’s amazing LS Positioner Fence Systems are now available in FULL METRIC VERSIONS. 
(Please click here for LS Metric Conversion Kits)
 
  The 32" x 21" Left-side router table permits maximum fence system range and offers open access from the end of the table saw by sliding the INCRA positioner assembly down the rails. This table is sized for saws with oversize cast iron tops measuring 30" - 31" deep along the miter slot.    
 
  The 32" x 32" Right-side router table serves double duty as a work surface extension and includes a full size 3/8" x 3/4" T-Slot Miter channel. This table is sized for saws with oversize cast iron tops measuring 30" - 31" deep along the miter slot.    
The INCRA Miter V120 Shopsmith Edition's adjustable miter bar will fit the Shopsmith
machines only and is not compatible
with the standard 3/4" x 3/8" miter slots found on most table saws and router tables. An incredible 120 angle stops are laser cut into the steel protractor, with a stop available for every whole degree and two special stops at 22.5 degrees
for cutting eight-sided frames and mouldings.

Don’t let the small size fool you!
The New INCRA Miter V120 puts high-resolution, repeatable accuracy within the budget of every woodworker. An incredible 120 angle stops are laser-cut into the steel protractor, with a stop available for every whole degree and two special stops at 22.5 degrees for cutting eight-sided
frames and mouldings.
The New INCRA Miter Slider SE combines the versatility of the INCRA Build-It products with the unique performance and feel of the adjustable GlideLOCK miter bar used on INCRA Miter Gauges. The steel bars are more rigid than any wooden or plastic runners. Exclusive at INCRA only
 
  The NEW INCRA Miter 1000HD is the most refined model yet in the Miter 1000 series.
The HD stands for High Definition, because the protractor plate's exclusive AngleLOCK Indexing System has a whopping 180 can't-miss angle stops in 1° increments with special stops located at 22-1/2°.

INCRA Launches Free Project Plans
Downdraft Cabinet by INCRA expert Mark Mueller, IN
Easy to make and extremely effective dust collection system that will be perfect for your router table. The Downdraft Cabinet uses common hardware store fasteners and hardware and is made with all wood construction. It's a great beneficial project for your shop.


Original INCRA Jig & Fence System                             

The INCRA Jig that started it all more than twenty years ago has been reissued, and the same qualities that made it such a knockout then are still relevant in workshops today. By adding a fence and a couple of simple fixtures (either shop-made or purchased as part of the INCRA Jig Fence System), 3/8” box joint and 1/2” dovetails can be produced equally spaced or variably spaced. The 1/2” dovetail template can also be made half-blind, through, sliding, or cornerpost.

For even more variety, the 11 box joint templates and 29 dovetail templates from the INCRA Master Reference Guide can be adapted to the Original INCRA Jig to produce literally billions of joinery variations.



INCRA Build-It System                                                  

These universal 5/8” MDF Panels are pre-cut and pre-drilled to instantly accept INCRA’s Miter Sliders and T-Slot Panel Connectors. Now you can build hundreds of your own custom jigs and fixtures in minutes with just a screwdriver and your imagination. The possibilities are endless!