|
 |
|
INCRA Miter 5000
Part Number: MITER5000 |
|
|
|
The Miter 5000 blends
the incremental angle control features of the Miter
3000SE with a very special 3-panel Sled for the
ultimate miter cutting workstation for the table
saw.
A Renewable Right Panel provides zero-clearance
tear-out control and cut-off support on Both sides
of the blade. Two aluminum T-tracks are embedded
in
the MDF panel top to secure an included work piece
hold-down clamp and to provide absolute rigid support
for the 36" to 64" telescoping IncraLOCK
Cut-off Fence. Will crosscut a 25" wide board
with full control on a standard 10" table saw.
The Miter5000 by INCRA delivers perfect, repeatable
accuracy.
First time, Every time,
Any angle. |
 |
INCRA Hold Down Clamp
Included with every Miter 5000 is this simple
and incredibly useful Hold Down Clamp which
locks your workpiece onto the sled for maximum
accuracy and the cleanest cuts possible. It
only takes seconds to use and provides the
rigidity needed for world class results.
|
|
|
| |
GlideLOCK
Miter Bar
The expansion disks adjust both sides of the bar
for ZERO side play, anti-friction travel on all table saws with standard 3/4" x 3/8" or near-standard miter gauge channels, including Delta, Craftsman, imports, etc. The miter bar's adjustment range accommodates actual slot widths between 0.740" and 0.760". |
|
|
| |
Special
Edition Telescoping
INCRA-LOCK Fence
This Special Edition Miter Fence telescopes
from 36" to a full 64" length. Includes
the
Dual Flip Shop Stop and INCRA's patented
Automatic Positioning
Control.
|
|
|
| |
AngleLOCK
Indexing
Precision angle indexing teeth are laser cut
in solid steel to lock in 364 positive angle
stops in 1/2°, 1° or 5° increments
over a full 180° range. it's also continuously
adjustable between 1/2° steps.
|
|
|
|
|
INCRA
Miter 5000 Sled for Shopsmith
Part Number: SMITER5000 |
|
In cooperation with
Shopsmith engineers, this version of the Miter 5000
Sled
has been specifically adapted to the Shopsmith Mark
V Series. This is the only Shopsmith authorized
miter sled on the market.
Miter 5000 Sled Replacement
Panel In Use
The Miter 5000 Sled is customized exactly for your
own saw by installing the entire sled and then making
a single cut through the right panel to give you
a "zero clearance" sled edge for excellent
workpiece support. This newly separated sled panel
is then locked in place using the included miter
channel locking devices (Incra Miter Sliders). Easily
removed and reattached this panel is permanently
used unless you change saws. Obviously any "zero
clearance" cut will be in the wrong place should
you change table saws and having a replacement panel
available keeps maintains the remarkable value of
your Miter 5000.
To replace your panel, you simply remove the secondary
panel at the T-Slot extrusion and then attach your
replacement panel. Once again you make a "zero
clearance" cut of the new panel and attach
the resulting piece as before. Below you can see
the same exact setup with a lefttilt Shopsmith saw. |
| |
| INCRA
Miter 5000 Features: |
|
| |
 364 Positive Stop in 1/2° Increments |
| |
Extender Fence Telescopes from 36" to
64" |
| |
GlideLOCK Miter Bar Adjusts to Fit Any Standard
Table Saw |
| |
INCRA Flip Shop Stop Positioner |
| |
Indexing Every 1/2° Plus Continuous Adjustment
Between |
| |
Right- and Left-tilt saw compatible |
| |
Fence lock down clamp for rock solid support |
| |
Miter Slider included for static sled panel
positioning |
|
