| | |  |  |  |  | | | Segmented
Ring Jig (plan#
008) |  |
| |  | One
of the more common methods for producing segmented rings uses a miter gauge to
control the angle
of the cut and a stop block clamped to the infeed end of
the table saw's rip fence to set the segment length. You simply trim the end of
a long piece of stock, flip the material and advance to contact the stop block,
then make another cut to part off the segment. While this "cut, flip,
advance, cut" routine is fairly quick, it does present a couple of problems.
First of all, the cut that removes each segment from the main stick always leaves
a cutoff nib on the segment, which must be sanded off before glue-up. Second,
flipping the stock after each cut means that in the final glue-up, every other
piece has a potentially different color in the grain creating a "checkerboard"
effect. The
simple jig shown here solves both of these problems. A common reference edge (the
outside of the ring) is maintained against the jig's fence during all of the angled
cuts to insure proper color and grain sequencing during glue-up and, since the
securely clamped segment is unable to move away from the blade, no cutoff
nib
is left to worry about. To
build this unique jig, begin by adding a Miter Slider to a small Build-It Panel.
Place in your table saw's miter slot and adjust for a good fit, then add a T-Slot
Panel Connector to each edge. Add a large Build-It Panel to cross the line of
cut and trim to the blade. Use the remaining piece of the large Build-It Panel
along with another Miter Slider to make the drop panel as described in Steps 3
through 7 shown on the reverse side of your Build-It Panel's wrapper. Cut the
slots in the fence as shown in Detail 3A, then attach using (2)
1/4-20
x 1-1/2" hex bolts with washers and Build-It Knobs. The slotted holes permit
adjustment to almost
any angle. Use test cuts to set your final fence angle
based on the number of segments desired and tighten the clamping knobs.
 | |
Build the toggle clamp platform shown in Fig 4 and Detail 4A, cutting
one end to 90° and the other end at the same angle required for your segments.
You can accurately make the angled cut using your Build-It Jig since
the fence
should be at the correct angle and position. Flip the platform upside down and
attach toggle clamps to favor
the edges of the platform as | |
| shown.
Allow enough of the toggle
clamps' arms to overhang the platform so that you
can reach to the center of your longest segment's length. Mark your jig's fence
and toggle clamp platform with the number of segments required to complete the
ring. |
OPERATION
Step
1. After ripping your stock to width, mark one edge with a line that
runs end to end then rough crosscut at 90° as many "blanks" as you
need for your project. Make these cuts about 1/8" - 1/4"
longer
than your desired finished length. Any
method can be used for these rough
cuts (even your bandsaw). You can number the pieces to maintain the grain alignments
during glue-up, Fig. 5 and
Detail 5A. Marked this way, segment
blank stock can be pre-cut and stored in plastic bags until
needed for future
projects.
| |
|
Step 2. Set the toggle clamp platform against
the fence on your Build-It Jig with the square end toward the blade. Set the distance
between the end of the platform and the blade so that you remove only a minimum
amount from your blanks then
lock the platform in place using a Build-It Clamp. Position
your segment blank with the reference edge against the fence, engage the toggle
clamp, and make your cut, Fig. 6. Repeat for one end of all of your blanks. Step
3. Reposition the toggle clamp platform against the fence with the
angled end toward the blade, Fig. 7. Set the final segment length by adjusting
the distance between the end of the platform and the blade, then lock the platform
in place with the Build-It Clamp. Now simply place each blank's reference edge
against the fence, nesting the previous cut against the end of the toggle clamp
platform and engage the toggle clamp to cut a perfect finished segment.
|
| |
|
|  |  |  |  |
|
|
| |
